BMW 2D datalogger extension box

Aloittaja murmela, 14.04.18 - klo:12:52

« edellinen - seuraava »

0 Jäsenet ja 1 Vieras katselee tätä aihetta.

murmela

Kopypastea muistiin jos joku sattuu joskus tarvitsemaan...

For the BMW sport bikes S 1000 RR and HP4 2D Debus & Diebold Meßsysteme offers professional measurement extensions for getting more out of your bike:
http://2d-datarecording.com/en/produkte/custom-packs/bmw-custom-packs/

For the BMW S1000RR are the following extensions available:
http://2d-datarecording.com/en/produkte/custom-packs/bmw-custom-packs/s1000rr-custom-pack/

S1000RR 2D logger extension box:
http://2d-datarecording.com/en/produkte/custom-packs/bmw-custom-packs/s1000rr-custom-pack/extension-box/

Datasheet:
http://2d-datarecording.com/Downloads/Datasheets/Amplifiers-and-interfaces/Pdf/IN-LSU_BMW-900.pdf

Driver:
http://2d-datarecording.com/Downloads/Treiber/atmel.zip

Art. No.: IN-LSU_BMW-900

Please note: For connecting two suspension potentiometers you need one adapter cable (One cable supports two potentiometers). Please order separately.

Art.-No. adapter cable: WL-IN_BMW-900

For calibrating sensors you need the software Race. The software is free of charge.
You can download it here:
http://2d-datarecording.com/Downloads/Setups/Race2015_Internet.EXE

With the extension box the HP race data logger can log data from two suspension potentiometers, two generic analog sensors and a lambda probe. It also controls the heating of the lambda probe. The box transmits the measurement data over the CAN-bus to the HP race data logger.

Pre-configured for direct application on the S1000RR CAN-Bus.
USB-Interface for initializing the analog sensors via a connected PC.
Supports up to two suspension sensors for front and rear, respectively.
Supports up to two generic analog sensors.
Supports one lambda probe.
Jarrut paskana, paha hidastaa.

murmela

14.04.18 - klo:13:09 #1 Viimeisin muokkaus: 14.04.18 - klo:14:18 käyttäjältä murmela
Ja ois yks kysymyskin jos joku sattuis tietämään.
Eli kun mulla on -11 mopo johon flässätty RCK2, ja esim 2D dataloggeri on konffattu käyttämään 2013 liittymää, niin ecun firmware ollee vanhempi kuin 2014, eli mun tarvii kysyy noilta jotain konffisoftaa??


Downloads -Setups -section:
http://2d-datarecording.com/en/downloads/setups/

RaceKit 2015
Setup for the 2D KIT systems Trackday and Bike with firmware 2014 or newer:
http://2d-datarecording.com/Downloads/Setups/RaceKit15.EXE

For older systems please contact us:
http://2d-datarecording.com/en/kontakt/


Dataloggerin PC softasta löytyy tuollainen:
Options - HP Race Datalogger settings - Changing HP Race Datalogger device software - 06 S 1000 RR HP4 2013+ -- 2d ExtensionBox
Jarrut paskana, paha hidastaa.

murmela

Noista voi olla hyötyä muissakin bimmerin CAN bus hommissa.

CAN bus, MQS, 8PF/M

8 Pin Female
front view

1 2 3 4 -

- 5 6 7 8

8 Pin Male
front view

- 4 3 2 1

8 7 6 5 -

Pin Name Description Color
1 n.c. Not connected
2 n.c. Not connected
3 KL 15 Switched power supply green
4 GND Ground brown
5 CAN-L CAN Low white
6 CAN-H CAN High black
7 n.c. Not connected
8 KL 30 Permanent power supply red
Jarrut paskana, paha hidastaa.

Powered by EzPortal